Included with every projector lamp we sell is our trusted Day Guarantee. If you order a projector lamp from our company and you are not satisfied for any reason, you may send the projector lamp back for a full refund or an exchange. Genuine original bulbs are manufactured to the identical strict quality control requirements as are found in original modules.
Shipping Calculator. Download Technical Diagram. If you have a question about the product specifications or the functionality of the lamp, please type it in here and contribute to the MPL community. If you have a question related to price or shipping please contact our helpful, accountable Customer Service. Search for the projector lamp you need! Save this page directly to your inbox! Free Shipping On Ground Orders.
Do not put small parts into the air intake vents. It may result in malfunction of the projector. Using it in dusty place may cause the poor picture quality. When using under the dusty or smoky conditions, dust may accumulate on the LCD panel and lens inside it, and may resultantly be projected on the screen together with the picture. When the above symptoms are noticed, please clean up the LCD panel and lens following to the "Cleaning Method".
The inside of the projector can become very hot. The glass can shatter and cause injury. Procedure 1 Turn off the projector and disconnect the AC cord. Allow the projector to cool for at least 45 minutes. Make sure that the lamp is set properly. Replace the lamp cover and tighten the screw. Note: - The projector cannot be turned-on with lamp cover removed, because when the lamp cover is removed, the lamp cover switch is also released to switch off the lamp circuit.
Service Par ts No. We recommend cleaning the air filter after the projection lamp is replaced. Refer to "Air Filter Cleaning". This is to indicate that lamp replacement is required. Mechanical Disassemblies Mechanical disassemble should be made following procedures in numerical order. Following steps show the basic procedures, therefore unnecessary step may be ignored. Caution: The parts and screws should be placed exactly the same position as the original otherwise it may cause loss of performance and product safety.
Disassembly requires a 2. Note: There is no mounting direction of the lens. Do not replace the LCD panel separately otherwise it cannot obtain proper picture. A Fig. These LCD panels are installed with precision at the factory. If there is, try to remove the shading following to the chapter "Optical Adjustment". If it needs the adjustment, adjust the white balance following to the "White Balance Adjustment" , "Gamma Adjustment" and "Common Centre Adjustment" in the chapter "Electrical Adjustment".
If you find the color shading at the some part of the screen, it needs to take the color shading adjustment. This adjustment should be performed by a computer and it also requires a special software "Color Shading Correction". Check the number on the arrows and mount each part according to its note; A: The printed part no. B: The printed part no. C: The printed part no. D: The printed part no. E: The cutting corner comes to this side up.
Adjustments after Parts Replacement? R-Contrast adjustment? G-Contrast adjustment? B-Contrast adjustment Integrator lens adjustment?
Relay lens-out adjustment? Fan control adjustment? Sub gain adjustment? Video center adjustment Electrical Adjustments Clamp adjustment? PSIG adjustment? Black reference adjustment? Common center adjustment? Gamma adjustment? White balance adjustment? White uniformity adjustment? Optical Adjustments Before taking optical adjustments below, remove the Cabinet Top following to the "Mechanical Disassemblies".
Adjustments require a 2. Optical adjustment requires a 2. Note: Do not disconnect connectors on the main board, because the projector cannot turn on due to operate the power failure protection. A 1 Loosen a screw A Fig. Repeat steps 1 to 3 for remaining polarized glasses. Polarized glass mounting base Fig. If the shading appears on the left or right of the screen as shown in Fig. Electrical Adjustments? The service menu appears on the screen as follows. To adjust service data Select the adjustment group no.
Refer to the "Service Adjustment Data Table" for further description of adjustment group no. Data 0 0 32 Ver. Item No. Projector Database 11, Projector Forums Login. Large Venue Classroom Interactive Conference. Find a Projector. Classroom Interactive Portable. Product Downloads Product Sheet. User Manual.
Similar Projectors. View Projector. Dukane ImagePro User Reviews 0.
0コメント